Wireless GSM Alarm System

Protection zone: 3 zoned wired ,16 zone wireless, 2 zone control output GSM 850 /900/1800/1900Mhz bands alarm base for the world Monitor living surroundings Voice and message alert 1 group alarm center number .3 groups common alarm number Send SMS or call to set arm disarm monitor output Com Function Com Function 1#1# Outdood alarm* (all detectors work) 1#2# Indoor alarm (part detectors work) 1#0# Disalarm *(all detectors not work) 3#1# Sounder immediately 3#0# Stop Sounder 4#1# Start to listen-in (use phone key )* 4#0# Stop to listen-in (use phone key ) 11#1# Need siren sound when alarming * 11#0# No siren sound when alarming12#1# Sending SMS when alarming * 12#0# No Send SMS when alarming 15#1# Dial phone number when alarming * 15#0# Just alarm and no dialing 16#1# Disable Relay close 3 Min when alarm 16#0#* Set Relay close 3 Min when alarm* 17#1# Set PSTN monitoring center avail 17#0# Set PSTN monitoring center disavail* 18#1# Dial out whan base change to alarm status 18#0# Not dial out whan base change to alarm status* 19#1# dialing whan base change to disalarm status 19#0# Not dial out whan base change to disalarm status* 30## show the alarm and disalarm status of every zone 31#--# Change password. Enter a new password (1—6 bit). 38#--# Set on alarm of zone (wireless zone: 1—16; wire zone: 21—23) 39#--# Set disalarm of zone (wireless zone: 1—16; wire zone: 21—23) 50## show preset phone number in the base 51#--# First group phone number(0—15bit) 52#--# Second group phone number(0—15bit) 53#--# Third group phone number(0—15bit) 54#--# fourth group phone number(0—15bit) 55#--# Fifth group phone number(0—15bit) 70## show center phone number. in the base 71#--#--# Set PSTN monitoring center phone number. 71# center number # room No. # 78#--# Set Dial out phone number whan you make base change to alarm status(this phone do not answer) 79#--# Set Dial out phone number whan you make base change to disalarm status(this phone do not answer) 80## show preset SMS in the base 81#--# First group Message(0—24bit) 82#--# Second group Message(0—24bit) 83#--# Third group Message(0—24bit) 84#--# Fourth group Message(0—24bit) 85#--# Fifth group Message(0—24bit) 86#--# Sixth group Message(0—24bit) 87#--# Seventh group Message(0—24bit) 90## show Output status in the base 91#1# Set Output 1 change to high 91#0# Set Output 1 change to low 92#1# Set Output 2 change to high 92#0# Set Output 2 change to low 93#1# Set talk to the base avail ( Output 3) 93#0# Set talk to the base disavail ( Output 3) 94#1# make two point of Relay close 94#0# make two point of Relay open 95#1# Set alarm when line input 1 open 95#0# Set alarm when line input 1connect to Gnd* 96#1# Set alarm when line input 2 open 96#0# Set alarm when line input 2connect to Gnd* 97#1# Set alarm when line input 3 open 97#0# Set alarm when line input 3connect to Gnd* Note: above table, ‘ * ’ stand for approves In the above phone operation, one beep shows you inter each number is successful, a long beep show you inter the sentence is successful, two short beeps shows you inter the sentence is failed, you should try again.In the above SMS operation, you will receive a answer message for confirmation after you send the message command to the base,thus you will know the working state of the base.(arm, disarm or alarm),if the answer is the present state of the base,you may send wrong seessage to the base. You also can only send the password to check out the present state of the base. The replied message as follows:Disarm,SMS-ON,Phone-ON,Siren-ON,monitor center -OFF, arm phone- OFF, Disarm phone-OFF SOME TECHNIQUE PARAMETER 1) Static current:20mA 2) Power:9V-12V DC 3) Working temperature:-20°C- +85°C 4) GSM850/900/1800/1900MHz band 5) Receiving code: ASK 6) Frequence:315/433/868/915MHZ 7) wireless distance: 100 M 8) wireless detectors:16 9) wire detectors:3