S54-31 Polyurethane Oil Tank Inside Wall Antistati

S54-31 Polyurethane Oil Tank Inside Wall Antistati

Changzhou, China
Production capacity:
1000 Ton / Year
Changzhou, China
Company
86-519-88231327
Yin Edward
Contact person

Basic Information

S54-31 Polyurethane Oil Tank Inside Wall Anticorrosive & Antistatic Coating (Two Component) Product description ØBased on hydroxide radical resin, electrically conducting pigment and fillers, isocyanate preformed polymer, fill added agent and solvent. Polyurethane coating. ØA, B two components. ØExcellent resistance to raw oil, 95/130 aviation spirit, aviation kerosene, 40# engine oil, 120# gasoline, kerosene, diesel fuel, benzene and such oil. And the paint will never cause any influence to the oil(pectin≤7mg/ 100mg). ØThe paint film is electric conductivity, it can avoid the accident caused by electrostatic accumulating. Ø No need for the primer, the dry thickness film can reach 150um, the film specific resistance less then 107Ω/cm. Recommended uses Oil resistant coating for the inside wall of the oil cabin, oil tank, oil pipeline and so on. Physical parameter ColorBlack GlossHalf-Glossy Theoretic coverage90 g/ Specific gravityAbout 1.00 Desiccation time25: surface dryness≤1h, Actual dryness≤24h Absolute solidification25: 7 days Flash pointA component: 29; B component: 30 Storage6 months Operation description Mixing ratioA: B = 7: 3 Curing time25: 20 minute Applicable time25: 4 hours ThinnerX-10 polyurethane paint thinner Operation methodAirless spraying Air spraying Manual brushing /Roller coat Max capacity of dilution5% 10% 3% Spout size0.4 0.5mm 2.0 2.5mm - Spry pressure13 15 Mpa 0.3 0.4 Mpa - Tool cleaningX-10 polyurethane paint thinner Film thicknessWet film: 90μm Dry film: 35μm Attention Ø The best condition of repaint: temperature 0 30, RH below 85%. Temperature of the base material should 3 higher than the dew point. Ø Adopt spraying, brushing, Roller; Different operating request different viscosity. Make sure using the X-10 Polyurethane coating thinner to adjust. Ø Its chemical reaction paint. Mixing around fully before operating according to the stated quota. Curing for 20 minutes before operating under 25 35. If temperature below 25, curing time should be expended. Use all the paint after curing up in 4 8 hours to avoid wasting. Ø The film will be completely solidifying after 7 days. Than can be used. Ø Avoid breath solvent vapor long time. Forbidden touching eyes and skin. Supply strong ventilation under narrow or unventilated condition. Protector is necessary. Packing specifications A: 21kg in 20L drum; B: 9kg in 10L drum anti-corrosion coating, anticorrosive coating, polyurethane coating

Delivery terms and packaging

Packaging Detail: 25kg/drum, 50kg/drum Delivery Detail: 15 days after 30% payment by T/T arrive
Port: Shanghai

Payment term

Telegraphic transfer

Фотографии

    Password recovery
    To recover your password, please enter in the box below your email address with which you have registered:
    The password reset code has been sent to your Email.
    Код уже был отправлен Вам ранее.
    Вы можете ввести его в поле выше, или получить новый код через сек.
    An error has occurred. Please check your e-mail address and try again.
    Ваш новый пароль:

    Name is empty


    Выберите страну доставки

    You have not written a message

    By clicking on the "Send" button, you agree that your data will be used to process your request. Further information and revocation instructions can be found in the data protection declaration.

    Your message has been sent!

    Close

    1
    Рынок B2B
    Cancel Close
      Show more close
        Area search
        Worldwide
        Категории
          Product