PTFE Teflon three-heater

PTFE Teflon three-heater PTFE Teflon three-heaterWATTSWOLTS (See pg 1)WIDTH IN/(mm)HOT ZONE IN/(mm)STD.VERT LENGTH In/(mm)MAX COLD ZONE In/(mm)MODEL NUMBERSHIP WGT Lbs/(kg)300024010618363HXO3210-06-11-**20480(255)(155)(460)(915)3HXO3410-06-11-**(10)6000240121018353HXO6212-10.5-17-**22480(305)(225)(460)(890)3HXO6412-10.5-17-**(10)9000240121218353HXO9212-16-23-**36480(305)(305)(460)(890)3HXO9412-16-23-**(17)12000240121918353HXO12212-20.5-29-**42480(305)(485)(460)(890)3HXO12212-20.5-29-**(20)15000240122018313HXO15212-25-35-**48480(305)(510)(460)(790)3HXO15412-25-35-**(22)18000240122218253HXO18212-29-40-**54480(305)(560)(460)(635)3HXO18412-29-40-**(25)Three-phase power is standard deploy, if want the single-phase please add “-1” before the over-temperature model. If required can be lengthen vertical length or use flexible riser. Please contact our Guangzhou Baoda electrothermal titanium product Co., Ltd.Product Features1.Adopt titanium, zirconium, SUS304 and SUS316 stainless steel to make, divide into vertical and heated at the bottom of "L", "Z" shape.2.According to the installation location , the chemical liquid’s nature, solid matter deposit characteristics in liquid to design the surface power of heat tube and decide the Tube diameter. Diameter general specifications: ø11mm,ø17mm,ø25mm,ø30mm,ø32mm,ø45mm,ø50mm.3.ø11mm, ø17mm tubes are shrinking tube heater, liquid heating, heat pipe surface power 5.6W/Cm2, apply to the mobility, and less solid Body deposition, Liquid does not precipitate in the heating surface of the liquid crystal heating after cooling.4.ø45mm diameter series products adopt low surface power design.5. Have 120V single-phase voltage, 220V, 380V, 220V three-phase, 380V three-phase, power from 0.5KW to 140KW.6. All heaters can be ancillary use with over-temperature protection switches and temperature probe.7. All heaters are adopt international inspection standards and ensure the electrical safetyInstallation and use1.The electric heater general through along the length (or width) direction, and well-distributed on one side (or both sides), that for not to collide during the operation. Installation near the slot-wall, also it can be placed between the plate and groove wall2.Electric heater can be fixed edge slot, slot-wall fixed, hanging rods and other highly installation, use wiring boards and support installation pieces with drilling then bolt tightening.3.All electric heater wire splice should pay attention to the balance of the three-phase, do not mistake grounded the 220v or 380v, and must grounded through the GFCI safety.4.Two electric heaters should maintain few spaces when installed, if each other two close make damaged easily.5.Ensure the hot zone (red marked below) must be immersed in the solution, or leading electric damaged by dry out. During the production process should be timely add the liquid and keep the calibration surface.6.During the heating, do not take the heater from the liquid, but after put off the power a few minutes later, remove heater after entire cooling.7.When use for high concentration solution heating, clean the heater with water after remove it from the tank, avoid the solution sediment be crystallization, agglomeration under low temperature on the heater.