circuit breaker for equipment

Introduction of TKM2-EB30 series (1)Scope of application Our TKM2-EB30 series CBE* are toggle typehydraulic-magnetic mode actuate circuit protection devices. CBE can furnish the protection function against overload and short-circuit of circuit in many applications. They are ideal for data processing and business machines, medical instrumentation, telecommunication equipment, vending machines , UPS, military applications and whenever precision operation is required. * CBE is an abbreviation of circuit breaker for equipment. (2)Features By adopting the magnetic mode with oil pressure tripping device, the circuit protection device is able to come true during the occurrence of overload and short-circuit. The tripping characteristics of TKM2-EB30 series CBE are more stable and precise. The tripping only depends on the magnetic force generated from the current flowing through the coil ,effect of environmental temperature variation is not a concern. Therefore people need not to think about taking capacity-reducing measures even though the temperature is high. The tripping mechanism does not involve with a thermal sensor, it doesnt need to wait for the device cooling down,as long as the fault current disappears, the breaker can be resetting to the ON (closing) position immediately. The viscosity of liquid pressure oil is influenced by the ambient temperature, its viscosity becomes thick under the circumstances of low temperature. The delayed tripping time becomes longer, it is necessary to offer enough additional time while starting the cold state equipment. On the contrary,the viscosity becomes thin under the circumstances of high temperature, the delayed time becomes short, so the circuit breaker is able to trip quickly. It leads to protect against the circuit over-current regardless of ambient temperature. The feature with inverse time-delay is advantageous for the overload protection. The calibration of the circuit breaker is more precise. It has trip free feature to insure that the contacts are separated when fault occurs. (3)Technical specification Conformity to the standard:GB17701-1999, IEC60934, UL489, EN 60934-2001. Rated voltages: UL 1P: AC 120V 2P : AC 120/240V VDE 1P,2P: AC 250V Rated current:6,8,10,15,16,20,25,30A Mode of operation:toggle handle Mechanical life[Endurance]:Total 10,000 times, with current 6,000 times, without current 4,000 times. Method of connection:Push-on terminal[may be with solder connection] as well as screw fastened terminal. Method of mounting:In case of one pole installation, only two screws are used for fastening CBE on the plate of the equipment. In case of two poles installation, four screws are required for mounting on the plate of the equipment. Insulation resistance:500VDC tester, over 100MΩ (new state) Interrupting capacity(Icn): UL 1P: AC 120V 5,000A; 2P: AC 240V 5,000A VDE 1P: AC 250V 2,000A; 2P :AC 250V 4,000A (4)Operating environment Ambient temperature:-20 85c Altitude:less than(or equal to)2,000m Relative air humidity:less than(or equal to)90% note: Do not install the equipment in a locations exposed to vibration, shock, dust, salt, corrosive gases, water drops, and oil. (5)Operation principle of hydraulic- magnetic tripping device By adoption of full magnetic mode with oil pressure tripping devices, the CBE carry out the tripping protection in the event of overload and short-circuit. The delayed tripping device employs an hydraulic-magnetic control with an oil dash pot. When over-current flow in the circuit, the magnetic force of the coil may overcomes the springs resistance, and the iron core will be moved toward the pole piece, subsequently pull down the armature and actuates the trip bar. In the case of short circuit, coil will generate extreme large magnetic force that instantly pull down the armature and make the trip. The delay of tripping can be caused by the viscosity of silicon oil. Once the tripping unit is actuated, the contacts will move apart and interrupt the circuit. (6)Ordering information When placing the order,please inform us of what kind of connecting method will be required in advance. In addition,please let us know about model,pole,rated current,rated voltage,applied standard,expected delivery and quantity.