6W RGB LED underground light

6W RGB LED underwater light The high power LED underground light is one of the lighting fixture used in water and is composed of high power LED. It is widely used in theme park lighting. Its bright and colorful lighting effect mixed by R,G,B beautify the environment and ornament the city LED underground light adopts stainless steel 316 housing, with good airtightness, dimmable lighting angle and can set address by coder, besides, connect DMX controller to realize many pcs lights’ color changing such as chasing, gradually changing, holistic changing etc..(More details to see Function Instruction) . LED underground light uses low voltage power supply, with high safety, low power consumption, long lifespan and good lasting. It matches 6-pin waterproof connecting cable and can work only to use together with our waterproof power supply and shape “T” cable. SpecificationParameter: PartNo. UH-JGYS1121-D51RGB ShellMaterial stainless steel 316 housing LEDQuantity highpower12LEDs(R4,G4,B4) Beamangle 6º, 15º, 25º, 25ºx 6, 40º, open beam IPRank IP68 Weight 2.6kg Dimension D260*H65mm Connector 6-pinwaterproofmaleconnector ElectronicParameter: Inputvoltage DC24V Maxpower 19.6W Communicationprotocol StandardDMX512controller Controlingsystem StandardDMX512controller+powersupply(advisetouseourwaterproofpowersupply)+coder Working Environment: Workingtemperature -20C +40 Immergedepth 0 2M Product features: 1,Realize RGB dimmable and various color changing by control of outer DMX controller; 2,Waterflow, chasing and other lighting effect are available if connect many pcs lights; 3,Standard DMX512 control way; 4,Dreamlike color changing when there is no controller. Function introduction 1.Coding (1)Put all the LED underwater lights in the right order (2)Connect the light’s transfering connection with coder’s signal output pole, DC 24V power input the accepting pole of the transfering connection. (3)Connect the output pole of transfering connection together with the light, then, power on. Choose coding button on the coder and set address for the first light(default to be 0001), then press confirm button to finish the 1st light’s coding. The light’s coding will be OK when it flashes green once for about 0.2 seconds During the coding. (4)Repeat step3 to set other lights’ address, the order will be 1,2,3,4,…,170. (5)The detailed installation and connection of underwater lights, please to see connection diagram. 2.Outer controller Underground light can be matched with our company’s DMX controller to realize RGB gradual changing, chasing, waterflow etc. color changing modes. More details to see the instructions of DMX controller. 3.This underground light can also be controlled by DMX512 console and get DMX channel automatically according to the coding-address. Every light occupy 3 DMX channel, every channel control the brightness of R/G/B respectively, total 255 rank. E.g., No.1 light’s DMX channel is 1,2,3, then, No.2 light’s DMX channel will be 4,5,6, others can be analogized in this way. One DMX512 console controls maximum 170 different address’(001,002,…,170) lights. Detailed DMX channel introduction is as below: CHANNEL ALTERRANGE CH1 0——255 RED CH2 0——255 GREEN CH3 0——255 BLUE 4.Automatic function When all lights have no any signal, they will be gradual changing mode and show dreamlike lighting. Remark: 1.)Every light’s cables at either end is 3m, each address can be used by many pcs lights, same address will be same color changing mode. 2.) Shape “T” cable’s distance is 2m(can be made according to the specific request of projects, should not be more than 30m.) 3.) The total length of 3-pin signal connecting cable should not be more than 100m, add signal amplifier if excess. Luminosity performance Standard light output(20 degreeenvironment) Illuminance Solution for common fault 1,If the light can not light, pls check whether power on or switch on2,If the light is on or off continuously, pls check whether power supply is loose or not touch well; whether the light’s connector not touch well. Note: If all above points still can not make the light work regularly, pls contact with professional person. Notice Points 1,To protect the shell, don’t wipe the light with rough res or cleanser and don’t rinse it with high-press water 2,Make light away from the dissolving chemicals to avoide light shell’s destroy 3,Should be used in -20 + 40, or, will shorten light’s lifespan 4,Pls don't use if the light to be mangle or has insulated problem 5,This light should be installed or repaired by professional person. 6,Pls contact supplier for related product’s information such as warranty, using environment and so on.