500mW IEEE 802.11a/n WIRELESS OUTDOOR CPE/AP/Bridg

IEEE 802.11a/n WIRELESS OUTDOOR CPE Chipset Atheros AR9280/AR7240 Transmit Power 27 dBm Receive Sensitivity -94 dBm @ 6 Mbps data rate Radio Specification Chipset Solution RF: Atheros AR9280 | CPU: AR7240 Antenna – Default configuration 16dBi integrated directional antenna (dual polarity) External RF connector 2 x sma-r connectors Antenna Configuration 2 * 2 (2 Tx, 2 Rx) Memory Flash DDR 8MB 32MB Modulation OFDM: BPSK, QPSK, 16-QAM, 64-QAM / DSSS: DBPSK, DQPSK, CCK Available Data Rates (Mbps) IEEE 802.11b – 11, 5.5, 2, 1 IEEE 802.11g – 54, 48, 36, 24, 18, 12, 9, 6 IEEE 802.11n (draft) – 135, 130, 121.5, 117, 108, 104, 81, 78, 65, 58.5, 54, 53, 40.5, 39, 27, 26, 19.5, 13.5, 13, 6.5, 6 RF Frequency USA (FCC) Europe (ETSI) 5.725GHz – 5.825GHz 5.470-5.725GHz / 5.725-5.825Ghz Average RF Output Power (± 1.5dB)* *actual power may vary based on regulatory requirements 802.11a 6-24Mbps 27 ± 1.5dBm 36Mbps 25 ± 1.5dBm 48Mbps 23 ± 1.5dBm 54Mbps 22 ± 1.5dBm 802.11n HT20 MCS 0 27 ± 1.5dBm MCS 15 21 ± 1.5dBm Receiver Sensitivity 802.11a 802.11n 6-24Mbps: ≤ -94dBm 54Mbps: ≤ -73dBm HT20/MSC0 ≤ -96dBm Regulatory Compliance FCC Part 15, CE EN300 328, EN301 489-1/17, EN60950 Standards Compliance IEEE 8802.11an, WiFi certificate Physical Specification Dimension 111mm(l)x256mm(w)x48mm(h) Weight TBD Enclosure IP65 Plastic Firmware Specification Function Detail Default setting Web Language English English Firmware Upgrade Method Web upgrade via Ethernet or Wireless port / TFTP upgrade via Etherent port Status Information Statistics for Wireless and Ethernet Connection status System Basic Settings Device Name APXXXXXX Country/Domain USA FCC Time NTP Disable IP Settings IP Address assignment (DHCP/Manual) DHCP / 192.168.1.1, DHCP is the default, however when server is not present the unit reverts to 192.168.1.1 RADIUS Accounting and Authentication Disable Wireless Basic Wireless Settings Operation mode (AP / CPE) AP AP mode functions 1. SSID Wireless 2. Hide SSID (enable/disable) Disable 3. Channel selection 149 4. Client limitations (0 32) 32 5. Wireless client isolation (enable/disable) Disable 6. Tx flow control (1 2400*64Kbps) 1687 Client mode functions 1. SSID ANY 2. CPE with Multi-Client support Enable 3. Tx Flow control by AP (enable/disable) Disable Wireless mode 802.11a/n Data Rate Selection 6-54Mbps & MCS0-7 Best Security Settings Open system Shared Key (64/128/152-bits WEP) 802.1X only WPA WPA2 WPA-PSK(TKIP) WPA2-PSK(AES) Open System Access Control Allow / Deny STA list STA Flow control for allowed stations Disable