1000mW high power 2.4Ghz b/g/n Enterprise Outdoor

1000mW high power 2.4Ghz b/g/n Enterprise Outdoor CPE/AP/Bridge Radio Specification Chipset Solution RF: Atheros AR9285 | CPU: AR7240 (400MHz) Antenna – Default configuration 8dBi integrated directional antenna (vertical pol.) External RF connector N type male connector – switchable by software Antenna Configuration 1 * 1 (1 Tx, 1 Rx) Memory Flash DDR 8MB 32MB Modulation OFDM: BPSK, QPSK, 16-QAM, 64-QAM / DSSS: DBPSK, DQPSK, CCK Available Data Rates (Mbps) IEEE 802.11b – 11, 5.5, 2, 1 IEEE 802.11g – 54, 48, 36, 24, 18, 12, 9, 6 IEEE 802.11n (draft) – 135, 130, 121.5, 117, 108, 104, 81, 78, 65, 58.5, 54, 53,40.5, 39, 27, 26, 19.5, 13.5, 13, 6.5, 6 RF Frequency USA (FCC) Europe (ETSI) 2.412GHz – 2.462GHz (Channels 1-11) 2.412GHz – 2.472GHz (Channels 1-13) IEEE 802.11gn HT40 ISM band 2.422Ghz – 2.452GHz (Channels 3-9) 2.422Ghz – 2.462GHz (Channels 3-11) Average RF Output Power (± 1.5dB)* *actual power may vary based on regulatory requirements 802.11b 28 ± 2dBm 802.11g 6-24Mbps 28 ±2dBm 36-48Mbps 25 ± 2dBm 54Mbps 24 ± 2dBm 802.11n HT20 MCS 0-3 26 ± 1.5dBm MCS 4 25 ± 1.5dBm MCS 5 24 ± 1.5dBm MCS 6 23 ± 1.5dBm MCS 7 22 ± 1.5dBm HT40 MCS 0-3 26 ± 1.5dBm MCS 4 25 ± 1.5dBm MCS 5 23 ± 1.5dBm MCS 6 22 ± 1.5dBm MCS 7 21 ± 1.5dBm Receiver Sensitivity 802.11b 802.11g 802.11n 1Mbps: ≤ -93dBm 54Mbps: ≤ -73dBm HT20/MSC0 ≤88dBm HT40/MSC0 ≤84dBm Regulatory Compliance FCC Part 15, CE EN300 328, EN301 489-1/17, EN60950 Standards IEEE 8802.11bgn, WiFi certificate Firmware Specification Function Detail Default setting Web Language English English Firmware Upgrade Method Web upgrade via Ethernet or Wireless port / TFTP upgrade via Etherent port Status Information Statistics for Wireless and Ethernet Connection status System Basic Settings Device Name APXXXXXX Country/Domain USA FCC Time NTP Disable IP Settings IP Address assignment (DHCP/Manual) DHCP / 192.168.1.1, DHCP is the default, however when server is not present the unit reverts to 192.168.1.1 RADIUS Accounting and Authentication Disable Wireless Basic Wireless Settings Operation mode (AP / CPE) AP AP mode functions 1. SSID Wireless 2. Hide SSID (enable/disable) Disable 3. Channel select (1-11) 1 4. Client limitations (0 32) 32 5. Wireless client isolation (enable/disable) Disable 6. Tx flow control (1 2400*64Kbps) 1687 Client mode functions 1. SSID Any Bridge mode Ap repeater mode