TD-5 Epoxy Mörtel, Emulsified Epoxidharz Groutin

TD-5 Emulsified Epoxy Resin Grouting Material Epoxy Mortar Description: This product is made up of emulsified epoxy resin \ additives and hard padding. It has a micro-expansion, fluidity, and good intensity \flexibility\ erosion resistance .The product has a great adhesion with various medium bases and it can be used in moisture base. Features: High intensity & flexibility: a good compression resistance ,super adhesion than general cement -based grouting material and strong adaptability for shaking environment.Fluidity: can fill the whole gap and accord to secondary grouting.Non-shrinkage: make sure close contact between equipment and foundation, make sure high-accuracy as required.Epoxy MortarLow-levelheat emission: operating time can reach as long as 120 min. (25°C\77 °F) .suitable for large volume grouting.Strong adhesion: can be used in moisture base ,and a good adhesion for concrete \ ceramic tile\ glass \ steel plate and various smooth base, excellent waterproof \ anti-leakage & acid-resistant.Erosion resistance: can burden long contact erosion with acid,alkali,salt,oil and other chemical products. Long endurance and conform to Green Environmental Protection Requirements.Application:It can be used in the secondary grouting installation of compressor \pump\punch machine \crusher\ball grinder\and other high vibration equipment etc. it can be also used in the grouting of equipment foundation section which subjects to chemical erosion.It can be used in the grouting of track foundation\ support saddle of bridge and other heavy-pressure section ; it can be also used in concrete strengthening and repairing work of architecture structure. Specification No. ItemsTest Index1 Fluidity(mm)≥2702 Vertical Expansion Rate (%)≥0.023 28days Bending Strength (M pa)≥54 28days Neutral Low Specific resistance(mm) 5.05 Compressive Strength (M pa)3days ≥206 7days ≥407 28days ≥558 Fastening Strength of Reinforcing Steel Bars(M pa)Round Bar ≥69 Deformed Bar ≥1310 Sulfuric Acid Ph=2 Non-dropping& Non-leakage with one year soaking 11 Hydrochloric Acid 2% Non-dropping& Non-leakage with one year soaking 12 Sodium Hydrate 10% Non-dropping& Non-leakage with one year soaking 13 Sodium Oxide Saturated Solution Non-dropping& Non-leakage with one year soaking Notes: 1. Compressive Strength:according to GB177-85 Strength of Cement Mastic Testing Method 2. Expansion Rate: according to GB119-88 Application of Cement Additives Technical Specifications How to use:1st . Surface preparation: The concrete surface ,which contacts grouting materials , should be hacked until exposes hard base , in order to make sure grouting surface cleaning \ dry and no oil . 2nd . Mould board installation: Mould board installation should be firm, and interface must be sealed (901 fast lack-stopping agent or YJS-400 adhesive is recommended). And the inside of mould board should be daubed with oil\ wax or PVC tape, to make mould board dropping easily. Epoxy Mortar 3rd . Mixing: (1) Mix Proportion :Part A :Part B: Part C = 1:3:30. (2) Check the quantity \ specification \ type and manufacture date, to make sure the product is within shelf-life. 2. (1) To begin with, mix Part A & Part B evenly (Deposited phenomenon for long Placement) and mix them according to the Mix Proportion of Part A: Part B = 1:3. And then stir them according to the Mix Proportion of Part A: Part B: Part C = 1:3:30 on one hand, and add the Part C slowly on the other hand .Make sure they are mixed evenly. (2) The mixing time is about 5-10 minutes, and in order to make sure the flowability of mixtures with low temperature, it is suitable to reduce the dosage of Part C or add some water to stir evenly. 4th Grouting construction: Grouting should from one side to another. Don’t knock down during grouting to make sure no air inside.If the grouting radius ≥1.5m , it should use elevated grouting and apply the theory of gravity head grouting5th Precautions: The mixed material should be used up within 45 min, and mixing-uneven or initial set mortar is prohibited.Long placement of Part A and Part B could appear slight layer phenomenon,so it is better to stir evenly before use.6th Picture about grouting method: Package & StoragePart A : 15±0.25 kg /bucket or 5±0.25 kg /bucket, 6 months from manufacture date stored in dry \ cool place (≥5°C\ 41°F)\non-sunlight exposure with original package sealed, and general freight transport is allowed.Part B : 45±0.5 kg /bucket or 15±0.5 kg /bucket, 6 months from manufacture date stored in dry \ cool place (≥5°C\ 41°F)\non-sunlight exposure with original package sealed, and general freight transport is allowed.Part C : 25±0.5 kg /bag, 6 months from manufacture date stored in dry \ cool place \ waterproof \ moisture proof with original package un-opened, and general freight transport is allowed.Epoxy Mortar