Elektrisches Nagel-Bohrgerät

SPECIFICATION OF THE Products Item:EB-A010Eco-friendly:YESOEM:WelcomeSize:50*44*30CMGross Weight:20KGNet Weight:18KGSample Time:5 DAYSProduce Time:10 DAYSMOQ:50 PCSMaterial:SAFEComposition:Packing:50PCS/CARTON ELECTRIC NAIL DRILL Safety Rules: Always unplug the nail drill when you change accessory or drill bits.Do not engage the shaft lock button while the manicure machine is running.Do not use the nail drill near water or place it in water. If motor falls into water, unplug it immediately and do not touch the waterDo not touch the bit or nail drill body after using it because the bit and body may too hot to be touched by bare hands.Keep dust out of you eyes and lungs by using a protective eyewear or a dust mask.Always “unpulg it after using the manicure machine.When not used, tool must be stired in a dry place and kept beyond the reach of childern. Products Item:EB-A010Eco-friendly:YESOEM:WelcomeSize:50*44*30CMGross Weight:20KGNet Weight:18KGSample Time:5 DAYSProduce Time:10 DAYSMOQ:50 PCSMaterial:SAFEComposition:Packing:50PCS/CARTON ELECTRIC NAIL DRILL Safety Rules: Always unplug the nail drill when you change accessory or drill bits.Do not engage the shaft lock button while the manicure machine is running.Do not use the nail drill near water or place it in water. If motor falls into water, unplug it immediately and do not touch the waterDo not touch the bit or nail drill body after using it because the bit and body may too hot to be touched by bare hands.Keep dust out of you eyes and lungs by using a protective eyewear or a dust mask.Always “unpulg it after using the manicure machine.When not used, tool must be stired in a dry place and kept beyond the reach of childern. Operation of the ELECTRIC NAIL DRILL: This tool is design for carver,engrave, rout, grind,sharpen,sand,polish.drill and more.Unplug the nail drill from electrical outlet before loading a bit.Press shaft lock button, Use the collect wrench to loosen the collet nut,inset the bit,and tighten the collet securely,But avoid ecdess tightening of the collet nut and never use a damaged bitTher eis an ON/OFF swtich, When the swithc is on, the tool runsWhen finished,turn off the nail drill and unplug itINSTRUCTION(NAIL DRILL): 1Assemble your tools and supplies. You will need your nail drill and the appropriate nails. Also, be sure that yourworkarea is level and clean.2Read the manufacturer's directions that accompanied the nail drill. This will help you determine what type of nails that you need, and any additional safety equipment, you always should use safety goggles. It will also tell you exactly how to load the nails into the drill.3Place marks on the piece of material you are about to nail. You can do this using the carpenter's pencil. These marks will indicate the desired spacing for the nails. Generally, you should place the nails at equal increments apart. For example, if you will be placing nails at 16 inches on center, then you place a nail in the center of the piece of material being nailed, and then 16 inches apart on either side until you reach the edge of the piece of material. To make these measurements ahead of time, mark them with the carpenter's pencil.4Connect the nail drill to the air compressor with an air hose. The air compressor should be turned to the MAP (maximum allowable pressure) setting, usually 120 lbs. Find the MAP for your specific nail drill in the instruction manual.5Place the nail drill over the mark you made on the wood. Wear your safety goggles and have a firm grip on the materials you are nailing. It may help to work with a partner.6Release the safety mechanism. Do this carefully. You should again refer to the instructions to determine exactly how to do this on your particular model. Never release this mechanism until you are prepared to nail.7Pull the trigger on the nail drill to release the nail. Continue to follow this step over every mark you made on the piece being joined. FOR MORE PRODUCTS INFORMATION, PLEASE VISIT WWW.EBUYCENTER.CN