DZSF Linearschwinger Für Coconut Shell Pow

Linear Vibrating Screen For Coconut Shell Powder Principle: Linear vibrating screen uses the vibration motor as vibration source, so that the material in the sieve was tossed at the same time move forward in a straight line, the material evenly from the feeder into the screening machine feed port, through the multi-screenNet generation of material specifications of the sieve, sieve materials were discharged from their export.With low energy consumption, high output, simple structure, easy maintenance, fully enclosed structure, no dust, automatic layout, more suitable for pipeline operations. Features Reliable, low consumption, low noise, long life, mode stability and screening efficiency. DZSF linear vibrating screen main features: 1. Tightness, and very little dust spilling. 2. Energy consumption, low noise, long life screen. 3. Screening of high precision, large capacity, simple structure. 4. Fully enclosed structure, automatic layout, more suitable for pipeline operations. 5. Sieve body parts are used rolled welded steel plate and profiles (part of the group as a bolt connection between the body) the overall stiffness is good, solid and reliable. DZSF main features of linear vibrating screen and for the industry: The product screening of high precision, large capacity, simple structure, low energy consumption, low noise, long life screen, sealing, and very little dust spilling, easy maintenance, can be used for assembly line production automation. The product is widely used in chemical, food, plastics, pharmaceuticals, metallurgy, glass, building materials, food, fertilizers, abrasives, ceramics and other industries in the dry powder or granular material screening. Linear vibrating screen structure: Function and principle: Department of the basic principles of the bottom of the motor shaft is installed by the heavy hammer (hammer Heng uneven), the motor rotary motion into a horizontal, vertical, inclined three elementary motions, and then communicated to the screen surface in the campaign.If you change the upper and lower parts of the heavy hammer of the phase angle can change the direction of travel of raw materials. Motor for use: This series motors meet the following conditions are rated for continuous output excitation force. 1, the vibration acceleration: no more than 7g (g: acceleration due to gravity) 2, the ambient temperature: not more than 40 °C 3, Altitude: not exceed 1000m 4, Power frequency: 50Hz 5, Voltage: 380V 6, the temperature rise: less than 80K (resistance method) Preparation before installation 1, check whether the requirements of the motor plate match. 2, with 500 volt megger insulation resistance measurement, the value of the stator windings should be dried, drying temperature should not exceed 120 °C. 3, check the motor of the fasteners, to guard against loose. 4, check the motor surface for damage, deformation. 5, check whether rotation and flexible, if unusual, should be excluded. 6, Check the power, whether phase, and no-load run for 5 minutes. Installation and adjustment 1, the motor should be fastened on the mounting surface, mounting surface must be smooth, flat. 2, the motor can be installed horizontally. 3, the electrical lead-core rubber cable with four-YZ-500V, then the power cable is not allowed when there is acute Lead off, and with the vibration of the body and firmly secured. 4, electrical grounding should be reliable, the motor grounding device, lead terminal signs, can also use foot bolts solid ground. 5, the exciting force adjustments. Use and maintenance 1, the machine shall be equipped with electrical protection device. 2, the machine is running early, check every day at least once a bolt to prevent loosening. 3, when the motor direction of rotation does not meet the requirements, you can adjust the power supply phase sequence. 4, the motor should guarantee good lubrication, each running about two weeks to add lithium grease (ZL-3) once, come on, through the oil by adding appropriate amount of lithium grease cup.When using sealed bearings, the motor is not installed on the oil cup. 5, the machine running total of 1500 hours, check the bearings, if serious injury should be immediately replaced. 6, the machine parked or garaged when used again after a long time, measure the insulation resistance should be used to measure 500-volt megger, should be greater than 0.5 MΩ. Routine maintenance 1, before the start: (1) Check the coarse mesh and fine mesh for damage (2) whether each set of locking ring beam 2, start time: (1) watch for abnormal noise (2) current is stable (3) whether the abnormal vibration 3,after use: clean after each usage. Regular maintenance Regular inspection coarse, fine mesh and spring without fatigue and damage, all parts of the fuselage is damaged due to vibration, the site must be added lubrication oil. Technical parameter