Diesel Oil Chassis Bohrgeräte

WFA5090DZJ(YD-) Geological Engineering Drilling RigsMain features1 The drill is equipped with full-hydraulic drive. 4100P diesel engine is used as hydraulic power supply to reduce the maximum extent of wear and tear for the vehicle.2 Give full play to hydraulic transmission to realize combination of multi-mechanism motion. It combines many functions such as hydrostatic swing, vibration pounding swing, rope hoisting heavy hammer shocked and static sounding etc. in one drill. The drill can drill with DTH drilling. 3 Fixed-combination which is composed by reveling power pack and vibratory hammer can lateral move apart from the hole site. That make it to be unprecedented in the country and abroad while solve such difficult problem that durning vibrating, it couldnt manage shock and swing. As a result, it has quite an effect on increasing competences of drilling and striping sleeves, installing and detaching drill rod easily, hoisting drill for a short time as well as dealing with accidents during subsurface boring. 4 It can satisfy the requirements of deep hole drilling with high applying pressure, high lifting force, high torque output and strong drilling capacity. 5 All mechanisms are controlled by hydraulic system with the advantages of high mechanization, convenient, quick and safe operation. 6 Revolving power pack is stepless gear shift with two mechanical shifts. 7 Hydromechanical drive with two gear shifts is adopted for the hoist. 8 At present, it is the most scientific and advanced prospecting drill with the highest performingin in country. Its work efficiency is 23 times higher than similar domestic products. Part of function and structure can match with the ones of the same category abroad, but the price is only a quarter of imported drills. It is indeed cheap and fine. 9 Chassis with 5 tons loading capacity of ground vehicle which is driven by double-axle is adopted to carry out stable rideability, trailer hitched and drilling tools loadable. 10 The drill will show its advantages in easy maintenance, quick and considerable after-service and promptly supply of spare parts. Major function 1 The drill can meets the requirements for all kinds of covering layer and in-situ test for quaternary geology stratification. It has been widely used in industrial and civil defense facilities, highway, railway, bridges, water conservancy, electric power, coal, oil, harbor, municipal projects, geophysical blasting hole and bedrock drilling, etc. 2 It has many functional characteristics, such as static pressure, rotation, vibration pounding, shocking and static sounding etc. Apparatus should be prepared by the customer, if the function of static sounding is used. A. Static pressure: it is used for drilling soft formation with pressing-in method and hydrostatic original sampling (static pressure and rotation can be used simultaneously if it is necessary). B. Static pressure and rotation: it is used for drilling various kinds of clay, sand layer of water table and bedrock weathering zone. C. Vibration pounding: it is used for drilling loose sand, scree and gravel stratum as well as running casing. D. Vibration pounding and static pressure: it can improve work efficiency and performance of drilling for A and C above. E. Static pressure, rotation and vibration pounding : it is the best way for the drilling of complex formation. F. Rope hoisting heavy hammer shocked: Hoisting heavy hammer to shock for drilling will be used when the speed of C above is slow. It also can finish hammering method original sampling and dynamic penetration as well as standard penetration test. G. Static rod in-situ H. Boring slurry retaining wall of quaternary geology, rock and deep hole can be finished by rotation cooperating with magma pumps. I. Drill with DTH: drilling can be finished on the rock via compressed air. Air compressor should be prepared by the customer, if the DTH drilling is necessary. Main Specification 1.Diameter of drill rod Ø42mmØ63mm 2.Diameter of boreholepile hole Ø400mm 3.Exploratory holeØ150mm final holeØ110mm 4.Depth of borehole aperture Ø400mm Depth 15m Ø150mm Depth 30m Ø130mm Depth 65m Ø110mm Depth 200m 5.System pressurerated 160 fcm2 Max. 180 fcm2 6.Elevating travel of power pack 4m 7.Promoted force of power pack rated10000 ·f Max.15000 ·f 8.Stress of power packrated 9000 ·f Max. 10000 ·f 9.Feed speed of power pack05mmin stepless speed regulating 10.Rapid hoisting speed of power pack lifting 19mmin lowering 28mmin 11.Rotational speed of power pack:0780 rpm 12.Torque of power packrated 625 ·m Max. 815 ·m 13.Frequency of vibratory hammer1100 min Max.shocking force 1000 f 14.Horizontal travel of power pack365mm 15.HoistMax.elevating power 3500 single-rope 16.Winding speed of hoist (two gears): 15m60mmin 17.punching torque of pipe removalMax. 500 f·m 18.Rotary speed of pipe removal48rpm 19.Continuous gyroscopic moment of pipe removal 250 ·m 20.Clamping diameter of gripping pliers Ø38Ø146mm 21.Clamping force of gripping pliers 1000 ·f 22.Lifting force of gripping pliers 4000 ·f 23.Downforce of gripping pliers 3000 ·f 24.Elevating travel 150mm 25.Model of the magma pumpBW450/BW150/H160 (BW450/BW150 power source and main machine share 4100P, H160 is hydraulic motor drive 26.Height of drill tower 7530mm 27.Power of dril495P model diesel engine power 40KW 28.Vehicle modelEQ1093 loading capacity Drive for vehicleFront and rear double-axle drive 29.complete weight of the vehicle85009400 30.overall dimension transport condition 7500×2470×3600mm operating condition7650×2470×7530mm