2640 Typ WC-Papiermaschine

1, Pulping equipment Description Qty Motor Power (KW) 8M3 high concentration Hydrapulper 1 55 2M2 high frequency vibrating screen 1 4 35M3 washing machine 4 11./5.5 φ380 disc refiner machine 3 37 φ700 propellers 10 7 Mixer 2 2.2 0.3M2 pressure screen 1 22 φ606 Cone desander 8 φ8 inch white pumps 1 18.5 φ4 inch pump station 7 4 6-inch addition to sand pump station 1 15 15-Roots vacuum pump 2 15 Note: The above is only brought within electrical equipment. 2, The host machine (A), the main technical parameters: 1, producing varieties: toilet paper 2, effective papermaking Width: 2640mm 3, quantitative :40g / m2 4, output :20 tons / day 5, the design speed: 180m/min 6, the working speed: 150m/min 7, gauge: 3600mm 8, compression method: pneumatic compression 9, Transmission: Division drive, VVVF 10, left phone: Customer Choice (B), the main structure and configuration of machine 1 Back roll φ500 × 3200 × 3600mm, 1 article. Roller body is seamless, wall thickness 12mm, coated plastic, rubber thickness 25mm, hardness 95 º ± 2. 1,1 Back for the adjustable roller stand, are cast iron type. 2 Rotary Department: from 2 sets of rotary screen and the device component. 2,1 Net cage φ1500 × 3200 × 3600mm, 2 only, spoke for the cast iron structure around the piece of stainless steel. 2,2 V Roller φ500 × 3200 × 3600mm, 2 roots, roller body is seamless steel pipe, thickness 12mm, coated plastic, rubber thickness 25mm, hardness of 35-38 º. 2,3 Felt guide roll φ219 × 3200 × 3600mm, roll body for the seamless steel pipe, wall thickness 12mm, chrome plated, for the 310311 bearing type. 2,4 Net control 2 sets of mobile water spray. 2,5 V roll cage and 2 sets of brackets, are cast iron structure. 2,6 Iron vacuum box 3, the board material for the polymer polyethylene panels 2,7 Sizing the form of Explorer into the pulp, without net slot (for the drawings, on-site cement to the system). 3 press section: from a main pressure, a squeezing of water formed 3,1 Squeeze water 1: φ450 × 3200 × 3600mm, 2 Article,roller body is cast iron coated with rubber, plastic thickness 15mm, hardness of 90 º. 3,2 Press on the roller: φ750 × 3200 × 3600mm, 1 article. for the natural granite body roll, surface polished, static balanced. 3,3 Squeezing roll: φ700 × 3200 × 3600mm, 1 Article. roller body is cast iron, coated plastic, rubber thickness 25mm, hardness 90 º ± 2, static balanced. 3,4 Felt guide roll for the φ219 × 3200 × 3600mm, roll body for the seamless steel pipe, wall thickness 12mm, chrome plated, bearing as 310,311. 3,5 Stretch roller φ245 × 3200 × 3600mm, roll body for the seamless steel pipe, wall thickness 12mm, coated plastic, rubber thickness 15mm, for the 310,311 bearing type. 3,6 Pneumatic compression device 2 sets, 2 each cylinder, gas control box 1. 3,7 Scraper device with a set of primary pressure, heavier type. 3,8 By drawing be installed for manual tensioner, manual calibration devices, playing blanket device (including motor). 3,9 Felt low pressure water jet pipe 1 set of double-sided. 4 Drying department: formed by the two φ2500 cylinder. 4,1φ2500 × 3150 × 3600mm cast iron dryer 2, the surface hardness of 210 º or above, static balanced, with bearings 3113156 type. 4,2φ650 × 3150 × 3600mm, a roller, roller body is cast iron, coated plastic, rubber thickness 25mm, hardness 95 º ± 2. 4,3φ550 × 3150 × 3600mm, a light roller, roller body is cast iron, coated plastic, rubber thickness 25mm, hardness 95 º ± 2. 4,4 True to the felt guide roll φ219 × 3200 × 3600mm, roll body for the seamless steel pipe, wall thickness 12mm, chrome plated, for the 310,311 bearing type. 4,5 Stretching roller φ245 × 3200 × 3600mm, roll body for the seamless steel pipe, wall thickness 12mm, coated plastic, rubber thickness 15mm, bearing type for the 310,311. 4,6 Cited paper rolls, spring rolls are φ159 × 3200 × 3600mm, the surface of copper, bearing 206. 4,7 By the Department of General Plan be installed for drying manual tensioner, manual calibration device. 4,8 Scraper device 3 sets, 2 sets of big-block scraper device. 4,9 φ2500 dryer Gear M = 12mm, z = 170,2 months, installed for bearings, bearing housings, air head, siphon. 4,10 Pneumatic tire roller 2, with steam control box. 5 Transmission Division: This machine is AC frequency division drive, the drive point with reducer, coupling, and other small gear. Motor, reducer early model calculation is as follows (in order to design calculation date). A pressure 45KW 650-type A big-block 30KW 500-type 2 Big Cylinder 30KW 500-type Reel 18.5KW 500-type Total power 123.5KW 6, the Department of Motor cover: a cylinder with double-layer aluminum hood, with φ800 axial fan 1 set. basis Department: Department of the machine network to track to track for the single slot, press section for the three slots to track, voluminous 360mm, drying the Department to track Single. Department of Single drive to track, along all ground screws, horn, oblique iron. 8, other: 8,1 The machine frame is heavy-duty cast iron square box structure. 8,2 If not available the Department, in accordance with General Plan requirements fully serviced.