2100 Typ WC-Papiermaschine

2100 type toilet paper machine (A), the main technical parameters: 1, Machine type:2100 type a third round four cylinder cylinder mesh paper machine 2,Producing varieties:toilet paper 3, Effective papermaking Width: 2100mm 4, Quantitative :120--250g / m2 5, Output :20 tons / day 6, The design speed:70m/min 7, The working speed: 40—60m/min 8, Gauge: 3000mm 9, Transmission: Division drive, VVVF(B), the main structure and configuration of machine 1. squeeze Mizube, 1 set. φ350 × 2550mm cast light on the roll, each under a cast iron roller, mechanical pressure. Bearing selection aligning bearing 113520. 2.rotary cage ,1 set φ1500 × 2450mm stainless steel mesh around the cage a chip. Network hub and thick carbon steel pipe material, spoke with strength of cast iron, stainless steel outer wrapping of Water film, to improve the treatment rate, around the chip size 1.5mm. Bearing Selection aligning bearings 113520. Bearing shell for cast iron, with labyrinth closed structure to prevent water seepage, bearing protection. Balancing treatment. 3. Couch ,1 set net surface located φ400 × 2450mm roll a rubber V, rubber thickness 25mm, rubber hardness 35-38 degrees, the maximum line pressure 3kg/cm2. Bearing with 312. Bearing shell for cast iron, with labyrinth closed structure to prevent water seepage, bearing protection. The seven-frame with a square frame, to track, pressure arm. Balancing treatment. 4. wind-style cage, 1 set cage made of high density polyethylene plate board production, into the pulp mouth, Boiling tank, air inlet, such as observation holes. sizing in the form of Explorer into the pulp, the Curved Adjustable pulp board, curved, wooden articles. pressure fan and seal. 5. Vacuum box, 3 sets of the iron box panels are made of high density polyethylene ,opening shape or form, or slit-shaped hole, the device can be rotated high-angle, suction device in the drive side. with 15 type vacuum pump 6. guide roller ,the numeber according to the drawings φ159 × 2550mm, 10mm thick seamless steel tube, red under the Bulkhead mounted, surface mounted FRP surface. bearing box is made of cast iron, bearings for the 309/310 double row radial ball bearings, aligning ball tile. Balancing treatment. 7. stretch Roll φ173 × 2550mm, 10mm thick seamless steel tube, red under the Bulkhead mounted, coated plastic, rubber hardness of 90 degrees, forward and reverse car thread, felt for the stretch. bearing box is made of cast iron, bearings for the 309/310 double row radial ball bearings, aligning ball tile. Balancing treatment. 8. High-pressure water spray pipe ,1 set. hydraulic spray equipment,nozzles made of stainless steel 9. Drying Section, 1 set. φ2500 × 2350mmHT250 cast iron dryer 1 set, which rise steeply lathe, surface roughness, fine cars, grinding polished, finish Δ9 above 210 degrees or higher Brinell hardness. design pressure 0.3MP, test the water pressure 0.6MP, bearing Spherical roller bearings with 3113156. with siphon, rotary steam head. 10. Roller, 1 set. φ450 × 2550mmHT250 a cast iron roller, rubber thickness 25mm, the surface pick grooves, rubber hardness 95 degrees, three corrugated air tire pressure, with steam control box. Use of bearings 113628. 11. Scraper ,two sets Scraper from the cylinder and the air bag pressure, so that each compression standard uniform gentle pressure with the cylinder at the blade surface to wrinkle even, and to protect the cylinder surface. 12. Hood ,1 set, Axial flow fan belt, blower. 13. Transmission Division with 650 reducer, cast iron, large cone, small cone, coupling. 14. Tight blanket device, transfer blanket device, play carpet installed for device design requirements in accordance with the drawings. 15. Department of cold roll cylinder φ900 × 2350mm cold cylinder 1 set, with gear, press the paper roller, bow exhibition roll etc.. 16. Rack Division All the cast iron trough rack and side cabinet rack, with the ground rail, anchor bolts, horn, oblique and iron.