业绩和运行情况XPE泡沫的机械(chemi

业绩和运行情况XPE泡沫的机械(chemi

原价: 500 000 USD
Changzhou Qu, 中国
生产能力:
100 单元 / 年
Changzhou Qu, 中国
公司
0086-0519-89188800
ye wang
联系人姓名

基本信息

XPE product is a new type of foamed plastic after LDPE material is chemically crosslinked and then foamed. XPE has better pliability than PS (polystyrene) foamed plastic, higher strength and better proofness than EPE, as well as better resistance to elements than PU foamed plastic. XPE material has good performance for secondary processing, and also can be compounded with steel plate, aluminum foil, sheet film, woven cloth, paper to turn into a new type of composite material. As a result, XPE products have a huge space to develop. It is because XPE material has so many advantages that this material is widely applied in architectural domain, such as roof insulation protective layer, water-proofing anti-freezing protective layers of underground engineering. In the industrial production filed, it is widely used in many machine rooms and a large number of pipelines heating and refrigerating, as well as water and oil transmission pipelines. The most use has been made of in automobile so far, mainly used in automobile interior trims, such as floor mat, overhead, trunk, as well as engine room for heat insulation, etc. It is also commonly used in culture, sports, toys for kids , all kinds of outdoor cushions, life jackets, sports protective devices, etc.Besides, XPE products can be widely used in the lining of bags and cases, as well as midsole for shoes. Characteristics of Foam Oven 1 Fan System: High efficiency low noise centrifugal fans are used. Stainless steel material is selected for impeller Fans utilize frequency converter to control the rotating speed for the realization of energy saving and nable matching . 2 Duct System: Based on Korean mode, measures are taken for our duct system to increase the number of ducts and enlarge inlet dimension, so as to control the wind speed within a reasonable scope. Make sure that the 30 times 3mm foam sheet can suspend above the central line of the foam oven. In the stage of foaming, we induce a lot of hot air into the rear of the inlet, so as to ensure PE sheet no together but can spread out in time in the case of foaming at an earlier time. 3 Energy-saving Measures for Foam Oven Mouth: The foam oven mouth is the place where the most of heat are eliminated. According to characteristics of derent products that we produce, a door that can float up and down is installed at the oven mouth. During the production of low multiplying factor products, the door may float down for the realization of energy saving. 4 Environment to Observe Foam Oven: For the existing foam ovens of Kore an mode and Korea-simulated mode, to observe the situation of foam sheet shall be from the oven mouth, while an observation hole is opened in the wallboard, so that we can observe thsituation of PE foam sheet at an earlier time.3 Main technical parameters equipmentMixer Machine TypeX(L)N55X(L)N75Power(Kw)75110output(kg/h)200 300300 450Pelletising Extruder TypeΦ120/12:1Φ135/9:1Power(Kw)4555output(kg/h)200 300300 450Sheet Extruder TypeΦ150/25:1Φ150/28:1Φ170/25:165/150one-step process without pelleterPower (Kw)160160180130output(kg/h)80 15090 180120 250120 250Horizontal Foam Machine

交货条款及包装

端口: shanghai

付款条款

Documents Against Acceptance

Documents Against Payment

Letter of credit

Telegraphic transfer

Фотографии

    密码恢复
    要恢复您的密码,请在下面您的电子邮件地址框与您已注册请输入:
    The password reset code has been sent to your Email.
    Код уже был отправлен Вам ранее.
    Вы можете ввести его в поле выше, или получить новый код через сек.
    发生了错误。请检查您的电子邮件地址,然后再试一次。
    Ваш новый пароль:

    名称为空


    Выберите страну доставки

    您还没有写消息

    By clicking on the "Send" button, you agree that your data will be used to process your request. Further information and revocation instructions can be found in the data protection declaration.

    已发送您的消息!

    親密

    1
    Рынок B2B
    取消
      查看更多
        地區搜索
        全球
        Категории
          产品名称