阁下你好-科技40M去IP无线摄影机

Wireless CameraIP camera also called network no-host camera, IP CAMERA, Network camera, or WEB camera, is a series surveillance equipment which can be used in various kinds of place. It can meet the requirement for monitoring without PC.Features: 1) Image sensor: 1/4-inch CMOS 2) Resolution: 300,000 pixels 3) Assign dynamic IP address automatically 4) Dynamic domain name analysis 5) Monitoring through internet browser 6) Embedded web server 7) Wi-Fi network transmission 8) Single/quad image display 9) Image format: MJPEG 10) Image resolution: VGA: 640 x 480 pixels QVGA: 320 x 240 pixels 11) Network interface: RJ45/10-100 base t, IEEE 802.b/g 12) Network agreement: TCP/IP, DHCP, SMPT, http, DDNS, UPNP and ICMP 13) Maximum frame rate: QVGA: 30fps VGA: 15fps 14) Supports motions detecting 15) Software upgrade: systematic software and web page upgrade 16) Monitor way: IE explorer 17) Replay method: Microsoft media player 18) Output drive: 1CH (5V DC/2a) 19) Trigger input: 1CH (close trigger) 20) Minimum illumination: 2.0Lux at 550nm 21) Supports auto white balance 22) Temperature: -10 to 50°C 23) Humidity: 20 to 80% 24) Voltage: 110 to 220V AC or 5V DC 25) Current: 2A 26) Power consumption: 2W 27) Dimensions: 120* 68* 38mm 28) Weight: 0.42kg IP Camera Quick Installation Steps: Connect network+power supply for ipcamUpdate IP: Open CD→double click ipcam search to seach ip address of ipcam, click UpdateIP to change ipcam’s ip address, netmask, gateway same as your computer’s ip address, netmask, gateway. (Please be noted: ip address’ last number must be different from other computer’s ip address to avoid conflict)View via LAN IE: Input IPCam’s ip address into IE brower to view via LAN IESetting router in order to view via WAN: enter into router, click virtual server (port map / portunnel / DMZ / port forwarding) to enable port (such as: 80, 81…) of ipcam’s ip address, such as: enableport 80 for 192.168.0.249, click add→confirm. (Please be noted: if port 80 is already used by other device, please change ipcam’s port into 81 or others via click UpdatePort to change port in ipcam search tool, and then enable ipcam’s new portView via WAN IP: enter into router→WAN status→Wan IP to find WAN IP of router, input WAN IP into IE brower, such as: 212.163.179.43 or 212.163.179.43:80 or 212.163.179.43:81, then you can view via static Wan IPDDNS: if you ip address is dynamic ip, you need to use DDNS function, pls go to oray.cn or dyndns.org or find a local DDNS service provider to apply for a DDNS account.PhotoModel No.SpecificationKDM-670430M IR Waterproof Wifi IP Camera1/4" CMOS, MJPEG, 36pcs ir leds, support IEEE 802.11b/g, IP65 PC System Request: Operate system: microsoft windows 98 se, me, 2000, xp cpu: 1.6g above related configure brouser: the 5. x of internet explorer or above picture plug-in: activex ( need not to do any non-safety setup) How to do router mapping: 1stexample: NETGEAR The first step in port forwarding is accessing the router. The ip address varies from router to router, so check the manufacturer's website or the handbook that was included when purchased. Next open your internet browser and type in the proper ip address according to the directions below. For NETGEAR the ip address is 192.168.0.1 and the default logins are as follows: username = admin password = password After logging on, you will arrive at the main setup page. Click on the port forwarding / port triggering tab on the bottom left hand-side of the screen. This will bring you to the port forwarding page. We're going to "add custom service", click this tab at the center of the page. 2nd example: LINKSYS For LINKSYS the ip address is 192.168.1.1 and the default logins are as follows: username = admin password = admin after logging on, you will see the main setup page. Click on the applications & gaming tab at the top of the page. This will bring you to the port range forward page. Here is where we will actually forward the ports as the page named implies.