carbon fiber film

Advantages Osign brand Carbon Fiber Vinyl are flexible PVC films with perfect adhesive intended to cover all type of the surfaces, such as wall covering, furniture, fixture, ceiling, doors, elevators, exterior/interior applications. Osign brand Carbon Fiber Vinyl are durable, dimensionally stable, vinyl films that were specifically developed for interior/exterior decorations and refurbishment. Effective Performance Life The warranty for Osign brand Carbon Fiber Vinyl for interior/exterior decoration as stated here extend to automotive or personal vehicle applications. The warranty applies to films that are exposed interior/exterior at a vertical angle (defined as +/-10°). A significant decrease in durability may be experienced if films are exposed other than vertically. Such non-vertical application should be based on Osign tests results and approval to determine acceptability. Effective Performance Life of unprinted interior/exterior Osign brand Carbon Fiber Vinyl depends on application exposure zones as follows. Fabrication Cutting with Electronic Systems Osign Carbon Fiber Vinyl is normally applied in sheets directly from the roll. In case people want to cut or screen print that is possible but not the primary intention of the film. Knife adjustment may be required as the product construction may differ from comparable products. The minimum height for text is 10 mm. Physical and Chemical Properties Values given are typical and are not for use in specifications. If a custom specification is desired, a request should be submitted through your sales representative. The following data is given for unprinted film. Application Temperature We recommends applying Carbon Fiber Vinyl products at 15°C - 38°C. Physical Properties Property Metric Units Thickness (Film + Adhesive) 0.170mm– 0.180 mm Elongation > 100 % Dimensional Stability (X-gash) > 0.3 mm max Abrasion Resistance Taber abrasion (0.5 kg load, CS-17) 1000 cycles Surface will be damaged Impact Resistance (Gardner at 0°C), 2 lb X 5 inch at 4°C No effect Humidity Resistance at 40°C (95% RH X 7 days) No effect Water Resistance (40°C water X 7 days) No effect Stain Resistance 18 hours Milk, Coffee, Wine, Lemon juice, Tea, Vinegar, Soybean oil, Salt water (1%), Ammonium water, Soap water (1%), Synthetic detergent, Hydrochloric acid (10%), Sodium hydroxide (10%) No effect Adhesion (N/25 mm) Substrate Adhesion (No Primer) Adhesion (W/DP-900N) Lauan Veneer 4.9 34.3 China Veneer 4.9 30.4 Plaster Board - 4.9* Asbestos Slate Board 4.9 34.3 Melamine-baked Steel Sheet 30.4 52 Phosphate-coated Steel Sheet 24.5 54 PVC-coated Steel Sheet 44.1 44.1 Aluminum 27.1 39 Stainless Steel Sheet 37.2 42 Acrylic Board 38.2 54.9 Mortar 3.9 21.6 Chemical Resistance Product applied to an aluminum panel, conditioned for 72 hours and then immersed in the chemical agents. Stain Resistance Carbon Fiber Vinyl product applied to an aluminum panel and placed in direct contact with the following substances at 20°C, 65%RH. Flammability Information about the new Carbon Fiber Vinyl approval numbers according to various test standards Approval Type, Number Product Type Test Substrate Classification Copy of Certificate IMO FW 646 Non-flammable substrate Non-combustible GPRD SBI EN 13823:2002 ST 553 Non-flammable substrate B-s2,do GPRD DIN 4102-1 Product Group 1-10 (all DI-NOC films) Non-flammable substrate B1 GPRD DIN 54837 PS, WG Non-flammable substrate Non-combustible GPRD FAR-25.853 WG 165 Non-flammable substrate Non-combustible GPRD Cleaning/Maintenance For cleaning of applied Carbon Fiber Vinyl use a soft textile with detergent and water. For heavy dirt accumulation use detergent and water at 70°C - 80°C. Removal Carbon Fiber Vinyl are removable with a heat gun at 80°C – 100°C or the Bosch steam remover PTL1 can be used. Shelf Life, Storage, Shipping The fabricator may store unprinted film for a period of up to three years. Film and markings must be stored in a clean area, free from excessive moisture and direct sunlight, on at least a 3" core with the film facing outward, with ambient temperatures of 35°C or less.