YJS-601 Таможенный углеродного волокна Клей / Клей

YJS-601 Bonded Carbon Fiber Glue \ Carbon Fiber Adhesive Features 1 With excellent corrosion resistance \ heat resistance\ well thixotropic property, reduce construction flow 2 Excellent penetration, Infiltration into the concrete surface easy. 3 Operating temperature 5°C\41°F ,do not construct when the humidity level ≥85%. Make sure there are no big difference of the temperature between the surface of the base and the construction environment. in order to prevent the dew from affecting the strength. Application:1 It can be used in stick construction of the carbon fiber sheet with the structure of concrete \ steel \ bricks etc. 2 It can be used in stick construction between the Carbon Fiber sheet and the tension structure of reinforced concrete. Standard: GB50367-2006 Specification: performance Items (M pa) condition Index Colloidal Performance Pull resistance 25°C \ 77°F 3days ≥70 elastic modulus 25°C \ 77°F 3days ≥12500 Tensile Strength 25°C \ 77°F 3days ≥40 Bending strength 25°C \ 77°F 3days ≥50 Aging Resistance Share Bond Strength of Steel- Steel 25°C \ 77°F 3days ≥14 Tensile bond strength of Steel- Steel 25°C \ 77°F 3days ≥30 Tensile Cohesive of Strength - Concrete 25°C \ 77°F 3days ≥2.5 cohesive failure of concrete Adhesion Artificial Hydrothermal Aging Shear Performance 2000 hours ≤10% Steps Project Design Surface preparation Coating of surface bottom The glue on the base hardening until to dry and do not stick your finger Make smooth The repair glue hardening until to dry, and do not stick your finger Coating the bonded Carbon Fiber Glue Stick the carbon fiber After it doesn’t stick your finger, stick the next carbon fiber hardening Checking and surface decoration How to use: 1 Clean the surface of the concrete with acetone. 2 Repair the concrete surface to smooth, please stop water or drainage if leaking. 3 Coating with glue on the base of the concrete, the thickness of the coating should accord to the temperature and the stick of construction. Warm up if the temperature under 5°C\41°F . 4 Cut the Carbon Fiber Sheet to required size before stick construction.( suggest size: 2 m more or less ) 5 The mixed glue should be used with in 30 min. 6 Put the glue accord to part-A:part-B=3:1 to the container, mix to even. If in summer or at a high temperature you can mix accord to part-A: part-B=4:1. 7 Use the roller in same direction of the Carbon Fiber sheet, roll again and again until the glue extrudes, in order to get rid of the air bubble and make sure the carbon fiber sheet good penetration. The connection of the sheets ≥10cm will be better. 8 During the multi-tier construction of the carbon fiber sheet, please stick the next sheet after the first surface of glue do not stick your finger. . 9 keep away from rainwater \ sand with wind during the harden time. And avoid the other hard stuff bump the bonded surface. 10 Hardening time ≥ 3-7days. Coating the surface as required after hardening. 11 the part-B may be change color during the life time, you can use it as usual. 12 During construction, if it contacts you or your eyes, please wash it with run water quickly. You need to see your doctor immediately on the serious condition. Package & Storage 1. Package: 12+4 kg /bucket 2. The product should be sealed in dry and clean house with the temperature of 0°C-40°C. 3. Shelf-life: 12 months. If it is beyond the 12 months, but afford to the qualified test, it still can be used. 4. The color of Part B may be changed during long-term storage, you can use it as usual.