YJS-502 Арматура-посадки анкерной Клей Клей

YJS-502 Rebar-planting Anchoring Glue\ Adhesive Features: Load bearing rapidly/ power anchoring /aging resistance/resistance to chemical attack/excellent water resistance.2 Micro slippage distance, it can control base material absciss the layer and deformation, Shrinking rate can decrease below 1%, and perfect dimension stability of bonded parts. Application: 1. It can be used in rebar-planting anchoring construction for reinforcing steel bar in concrete/brick wall/stone etc.2. It can be used in rebar-planting anchoring construction for reinforcing steel bar in all kinds of bearing load/ non-load bearing bolt and concrete/brick wall/stone etc.Standard: YB/T9261-98Specifications: Performance ItemsStandard Colloidal Performance Tensile Strength(M pa)≥30 Bending Strength(M pa)≥150 Compressive Strength(M pa)≥160 Adhesion Steel- Steel Share Bond Strength(M pa)≥16 Steel- Steel pull Strength(M pa)≥33 Deformed Steel bar & C30 concrete ¢ 25≥11 With Cement bonding Strength(M pa) C60 ¢ 25≥17 Rebar-planting Parameter Diameter (D) of bore big or small is determined by reinforcing steel bar diameter (d) and surface condition.(1)d≤12mm D=d+4mm (2)12mm<d<20mm D=d+6mm (3)d≥20mm D=d+8mm 2. Adopt YJS-502 Rebar-planting Anchoring Glue\Adhesive. Rebar-planting Condition: the bore depth (L)/ reinforcing steel bar diameter (d)=10. Because construction site is intricate, the bore depth (L) is 10d-15d-20d. With the increase of reinforcing steel bar diameter (d), the bore depth (L) should also be increase. Construction Process: Instrument explore and fix position bore & measure depth clean the hole and derust the reinforcing steel bar Mix glue fill glue spin and press-in reinforcing steel bar harden quality inspection Specification Part A Cream white viscous plaster Part B: grey and black viscous plaster, the mixing density is 1.7*10³kg/m³ 1. Bore /hole diameter/hole depth/ reinforcing steel bar diameter should accord to the requirement of engineering to design. 2. The hole wall should use hard brush brushing and clean up the dust of hole to make it clean and dry. 3. Reinforcing steel bar should be wipe off the grease and rust, then scour it use acetone. 4. Mixing 1)The filling of glue is easy to precipitate, but not influence strength. Mix evenly before used.( using the same bar to mix part A and part B is prohibited.) 2)According to Mix proportion: part A:part B=4:1 and stir it evenly . 3)The suitable volume ≤ 5kg. 5. Full fill the bore with glue 6. Spin and plug the rebar-planting into the bottom of bore 7. Don’t shake the reinforcing steel bar before it is hardened. 8. Do the pulling test to the Reinforcing steel bar of the important section. 9. The operation time of mixed glue (part A & part B) is 30-45 min under normal temperature. Package& Storage 1. Package: 4+1 kg /units, or 16+4kg/units 2. The product should be sealed in dry and clean house with the temperature of 0°C-40°C. 3. Shelf-life: 12 months. If it is beyond the 12 months, but afford to the qualified test, it still can be used. 4. The color of part B may be changed during long-term storage, you can use it as usual. Notice The information, and, in particular, the recommendations relating to the use of our products, are given in good faith based on ours’ current knowledge and experience of the products when properly stored , handled and applied under normal conditions in accordance with ours’ recommendations. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information.