порошок точка-стружечных горячего расплава покрытие машины

hot melt Coating machine ProcessBase cloth orientation opening selvage justifying coating curing Flat padding and cooling winding hot melt coating machine Brief Introduction 2.1 The principle of the powderpoint -bonded hot meltcoating machineprocess is: first the thermosol powder was softened and shaped on the engraved roller, then passing through the surface of the heated fabric, the melted powder transfer to the fabric surface to fulfill the powder dot transfer, finally, the powder fixed to the surface via curing closely. 2.2 During the whole process, the stability of temperature plays an important role, while the variation of speed exerts direct influence on the temperature change, so in the production, it is essential to master the relationship between the speed and the temperature, as well as how to control parameters of the whole machine. 2.3 To keep the uniformity of the product quality, operators must operate strictly according to the manual. structure and features3.1 Inlet frame and open-width selvage justifying machine 3.1.1 The main function of inlet frame is to adjust the tension when the matrix enters into the frame head; different tension of different substrate is adjusted by different delivery and tension frame. 3.1.2 Width opening selvage justifying machine assures the substrate smoothly and precisely enter into the frame head, reduce or diminish unevenness of coating by the substrate flipping. This system greatly improves the finished product ratio and reduces the labor intensity. 3.2 Powder dot hot melt coating machine 3.2.1 This section is the core heart of the whole process, preheating roller is used to preheat the coated fabric for water removal and fabric heating, main heating roller is used to fulfill the thermosol powder transfer, engraved roller is used to soften and shape the powder, auxiliary heating roller is used to assist the powder transfer. 3.2.2 The four rollers have different functions, but their surface temperature must be uniform and keep constant during the whole process. 3.2.3 All the heating roller in this machine is heat by built-in oil .we adopt imported three-phase voltage regulating automatic temperature control system, the roller temperature is stable and uniform. The surface temperature difference of the heating rollers is less than +-2Centigrades and it changes between +-2Centigrades. 3.2.4 As heat continuously transfers to the surface of engraved roller from the heating roller through substrate, different thermosol should adopt different heat insulating method. Except for HDPE, this heating system is normally used for preheating, in addition, in practical operation, cooling water is also needed to keep the surface temperature not too high. The temperature control panel show that the temperature is less than 2 centigrades. 3.3 Dryer 3.3.1 The dryer is used to cure the fabric coated with thermosol powder , thus the powder is fixed on the fabric surface closely. 3.3.2 Too low temperature of the dryer leads to powder drop off while too high temperature leads to fabric weathering, the handle of finished garment is stiff. 3.3.3 Temperature control system of the dryer adopts imported three-phase voltage regulating automatic temperature control system, so it is constant and the quality is good. 3.4 Flat padding and cooling device 3.4.1 Cooling the manufactured products, parts of them should be processed calendaring finish. 3.5 Winding device 3.5.1 Mechanical friction winding or hydraulic winding is available for product winding. 4 Operation and Adjustment 4.1Raise the temperature for preheating 4.1.1Based on the requirements, set temperature of roller and dryer, turn on the heating units. During heating, all rollers must be in running state to maintain the uniform temperature of the roller surface and avoid deformation. Static temperature arising is banned, powder point roller and recycle pump are in running state. 4.2Frame head coating. 4.2.1After surface of heating unit arrives at the set temperature, open the cooling water of padder, then feed the fabric for coating, 30 meters of leader cloth must be loaded to cut off the product damage.after feeding the leader cloth, start the hold-back creel, opening roller and photoelectrical selvage justifying system, when the fabric enters into the host machine, add the powder into the bunker for coating. Main Technical Parameters:ItemsParametersProduct Width(mm)12001600Production Speed(m/min)10 30Installed General Power60KW 380V80KW 380VOverall Dimension(mm)(L*W*H)9000×2100×26009000×2400×2600Weight(T)67.5