PoE с одним портом Разветвленная сеть дистанционного питания

poe Equipment description Features and Functions PROCET PT- PSE108G-Tis a single-port split network remote power supply device. It is suitable for indoor, meet IEEE802.3at standard ,can work normally between 100VAC 280VAC input voltage. This power supply use category super type 5 cable to connect to other network termination equipments, is suitable for 10/100/1000M network environment,effect distance of power supply is 100M. PROCET PT- PSE108G-T POE has the following excellent performance: 1.The power circuit has the function of Input over or under voltage, output over voltage, output over-current short-circuit protection for each circuit. 2.System reliability:MTBF>100k hours. 3.Conducted interference(CE)and Radiated interference(RE),comply with EN55022, CLASS B standard. 4.Lightning protection: Both positive and negative port of AC input can take 5KB, 8/20uS pulse current for 5 times, with interval of one minute. Power supply lightning protection circuit has the failure alarm function and safety protection devices like insurance tube etc. Operating Environment 1.Temperature: -15°C +55°C 2.Relative humidity: 5% 90%RH 3.Places that are ventilate and cool, clean, no conductive dust, no corrosive gases. 4.Places without explosion hazard. Technical characteristics and parameters 1.Input voltage: 100VAC 280VAC,47Hz 63Hz. 2.Maximum power output: 36W. 3.Output voltage regulation accuracy: -48VDC±2%. 4.Load regulation: -48VDC±1%. 5.Operating temperature range: -15°C +55°C. 6.DC output voltage of broadband noise: 3.4kHz 150kHz≤50mv Dimensions and weight: Width: 60mm Length: 160mm Height: 32mm Weight: <160g Remote power supply protection: Range of output over-voltage protection: -52VDC -50VDC Over-current protection(Single circuit): 350Ma 400Ma Over voltage protection: Input voltage over 290VAC 310VAC Over voltage recovery point: Input voltage over 285VAC Under voltage protection: Input voltage under 80VAC 85VAC Under voltage recovery point: Input voltage under 90VAC Over-temperature protection: >100°C PROCET PT- PSE108G-T structure appearance Ethernet ports light instructions Red light POWER on:Show power working normally Green light ACTIVE on: show equipment supply power normally Installation and Commissioning 1.Connected output signal line respectively (see chart) 2.Connect communicating & introducing line, signal wire, output lines tightly to avoid bad contacts and loose. 3. Insert the input power line into 110-220VAC introducing input socket Equipment description Features and Functions PROCET PT- PSE108G-Tis a single-port split network remote power supply device. It is suitable for indoor, meet IEEE802.3at standard ,can work normally between 100VAC 280VAC input voltage. This power supply use category super type 5 cable to connect to other network termination equipments, is suitable for 10/100/1000M network environment,effect distance of power supply is 100M. PROCET PT- PSE108G-T POE has the following excellent performance: 1.The power circuit has the function of Input over or under voltage, output over voltage, output over-current short-circuit protection for each circuit. 2.System reliability:MTBF>100k hours. 3.Conducted interference(CE)and Radiated interference(RE),comply with EN55022, CLASS B standard. 4.Lightning protection: Both positive and negative port of AC input can take 5KB, 8/20uS pulse current for 5 times, with interval of one minute. Power supply lightning protection circuit has the failure alarm function and safety protection devices like insurance tube etc. Operating Environment 1.Temperature: -15°C +55°C 2.Relative humidity: 5% 90%RH 3.Places that are ventilate and cool, clean, no conductive dust, no corrosive gases. 4.Places without explosion hazard. Technical characteristics and parameters 1.Input voltage: 100VAC 280VAC,47Hz 63Hz. 2.Maximum power output: 36W. 3.Output voltage regulation accuracy: -48VDC±2%. 4.Load regulation: -48VDC±1%. 5.Operating temperature range: -15°C +55°C. 6.DC output voltage of broadband noise: 3.4kHz 150kHz≤50mv Dimensions and weight: Width: 60mm Length: 160mm Height: 32mm Weight: <160g Remote power supply protection: Range of output over-voltage protection: -52VDC -50VDC Over-current protection(Single circuit): 350Ma 400Ma Over voltage protection: Input voltage over 290VAC 310VAC Over voltage recovery point: Input voltage over 285VAC Under voltage protection: Input voltage under 80VAC 85VAC Under voltage recovery point: Input voltage under 90VAC Over-temperature protection: >100°C PROCET PT- PSE108G-T structure appearance Ethernet ports light instructions Red light POWER on:Show power working normally Green light ACTIVE on: show equipment supply power normally Installation and Commissioning 1.Connected output signal line respectively (see chart) 2.Connect communicating & introducing line, signal wire, output lines tightly to avoid bad contacts and loose. 3. Insert the input power line into 110-220VAC introducing input socket