пластиковые машины для литья KLB82PC

plastic moulding machine KLB82PC isaspecialized blow moulding machine for PCmaterial. The feather of blow moulding machine KLB82PC: 1.Double tiebar, imported linear guideways 2.Hard gear surface reducer 3. Yuken hydraulic system 4. Controlled by Omron PLC 5. Inverter OMRON 6.Temperature control moduleOMRON 7. Relay OMRON 8. Contactor TE 9. Sevor motor KLB82PC hollow blow molding machine is the new generation of large plastic hollow blow molding machine produced by our company, it is mainly used to blow PC material products with the purify water barrel. This machine is composed of the main mechanism, electric system, hydraulic system, air passage, waterway and optional functional parts, etc. The main mechanism includes: extruding device, die head of accumulator cylinder, mold opening and clamping mechanism,hoisting device, bottom blowing device, robot (optional), etc. Electric part includes: heating and temperature control system of die head and extruder; parison controller system; PLC and relevant protective system, etc. Hydraulic system includes: hydraulic source, relevant pressure, direction and flow rate control part. Air passage system includes: driving part of robot air cylinder and blow molding part of products. Waterway system includes: cooling circuit for mold and other parts. Extrudingblow molding is adopted. The extruder with oil motor control can supply enough power. The plasticized and melting plastic is extruded to the accumulator die head by the extruder, when accumulating to certain volume, the opening degree of the mold will be continuously changed, the plastic will be injected into parison and enters the mold for blow molding, and then the robot (optional) will take out the product to complete a cycle. Optional functional parts of this machine includes: bottom blow device, robot, parison control system, etc. Configuration will be decided according to the order. Main characters of this machine: (1). Mold opening and clamping mechanism adopts double-pull rod structure with good rigidity, and the mold opening and clamping mechanism has a wide space. The die head is designed with the principle first in, first out. The parison has an even thickness, and the products have good mechanical properties. (2). High automatization, it can fulfill the whole automatic cycle from material loading to unloading of finished products.1. Main technical parameters of KLB82PC Unit ItemSpecificationMachine typeKLB82PCAccumulator headExtruding unitmax. container capacity 20 L screw diameter 82 special for PC mm screw L/D ratio 30:1 L/D screw speed 1080 rev./min plasticizing capacity 90 kg/h number of heating zone 5 zone extruder heating power 25 kw extruder driving power 45 kw Die headmax accumulator capacity 1.6 L max injection speed 1 kg/sec max head tooling diameter 80-130 mm die head heating zone 4 zone die head heating power 19 kw Clamping unitplaten valid size(w×h) 800×800 mm platen daylight 250800 mm clamping force 190 kn Bottom blowing unit(optional)expansion stroke 140350 mm blow pin auto-lifting stroke 100 mm blow pin manual-lifting stroke 200 mm Robot arm (optional)moving stroke 1000 mm Machine framelifting stroke 350 mm lifting speed 30 mm/min Hydraulic systemmain-pump rated pressure 12 mpa main-pump rated volume 180 L/min hydraulic driving power 45 kw parison control hydraulic servo system optional Rated volume 23 L/min hydraulic pump power 4 kw Pneumatic systemmax. pressure 8 kg/cm2 operating pressure 0.6 mpa air consumption 0.4 m3/min Water sourcewater supply pressure 0.3 mpa ElectricityVoltage AC380±10% V Frequency 50 HZ Phase 3 phase 4 wire Installation capacitytotal rated power 120 kw average consumption 53 kw/h total weight 13 ton dimension(L×W×H) 5600×2900×4500 mm