ограждение барабан машины

guard railroll forming machine The structure of equipment 1, Hydraulic decoiler l Single unrolling machine, one side can put material l Adopt automatic hydraulic system l Coil weight (Max):7000kg l Coil dia (Max):1600mm l Oil cylinder dia:1200mm working pressure: 10mpa l Coil Width(Max.):500mm 2, feeding, leveling l feed into unit oriented wheel(can right and left adjust) l into feeding roller, dia is 180mm,material 45# steel, quenched 48°-52°, chromed leveling is three roller above and four roller below, quenched and chromed 3, punching (can right and left adjust) l using hydraulic punching l oil cylinder dia: 140mm l working pressure:20mpa l mould material: Cr12 quenched 58°-62° l hydraulic power:7.5kw l size: 1.5m long*1.1m wide*1.2m high 4,roll forming l main motor power: 45kw l Decelerating motor: BWD14-43-37kw, made in Shanghai or Changzhou l drive: gimbal driving,120*500 l main shaft dia: 100mm material: 45forge steel l roller material: GCR15 quenched 58°-62°,chromed l roll station:17stations l Timing by transducer:5m--20m/min(not including punching) l Transducer: Panasonic made in Japan. 380V 50HZ l Computer: PLC l Computer operating panel: touching screen 5, cutting l hydraulic cut l knife material: Cr12,quenched 58°-62° l oil cylinder dia:250mm l working pressure:30mpa l working journey: 80mm 6, the Outside size: l 18m long*2.2m wide*1.5m high 7, Run out table l Jointed by 60mm*40mm tube (can be adjusted to up and down) l size:1.5mlong*0.8mwide*0.6-1mhigh(can be adjusted) The parts of machine l hydraulic passive Uncoiled, Forming Machine ( feeding, leveler, roll mill, cutting, punching, PLC computer, Hydraulic station, cutting), and simple run out shelves 3pcs, packing list 1 pcs. 4:The production flow of equipment DecoilingFeeding(take the sheet to the first station)leveling----Punching of the sheet roll forming----hydraulic cut to lengthproduct packing manual guard railroll forming machine The structure of equipment 1, Hydraulic decoiler l Single unrolling machine, one side can put material l Adopt automatic hydraulic system l Coil weight (Max):7000kg l Coil dia (Max):1600mm l Oil cylinder dia:1200mm working pressure: 10mpa l Coil Width(Max.):500mm 2, feeding, leveling l feed into unit oriented wheel(can right and left adjust) l into feeding roller, dia is 180mm,material 45# steel, quenched 48°-52°, chromed leveling is three roller above and four roller below, quenched and chromed 3, punching (can right and left adjust) l using hydraulic punching l oil cylinder dia: 140mm l working pressure:20mpa l mould material: Cr12 quenched 58°-62° l hydraulic power:7.5kw l size: 1.5m long*1.1m wide*1.2m high 4,roll forming l main motor power: 45kw l Decelerating motor: BWD14-43-37kw, made in Shanghai or Changzhou l drive: gimbal driving,120*500 l main shaft dia: 100mm material: 45forge steel l roller material: GCR15 quenched 58°-62°,chromed l roll station:17stations l Timing by transducer:5m--20m/min(not including punching) l Transducer: Panasonic made in Japan. 380V 50HZ l Computer: PLC l Computer operating panel: touching screen 5, cutting l hydraulic cut l knife material: Cr12,quenched 58°-62° l oil cylinder dia:250mm l working pressure:30mpa l working journey: 80mm 6, the Outside size: l 18m long*2.2m wide*1.5m high 7, Run out table l Jointed by 60mm*40mm tube (can be adjusted to up and down) l size:1.5mlong*0.8mwide*0.6-1mhigh(can be adjusted) The parts of machine l hydraulic passive Uncoiled, Forming Machine ( feeding, leveler, roll mill, cutting, punching, PLC computer, Hydraulic station, cutting), and simple run out shelves 3pcs, packing list 1 pcs. 4:The production flow of equipment DecoilingFeeding(take the sheet to the first station)leveling----Punching of the sheet roll forming----hydraulic cut to lengthproduct packing manual