Электрохимический алюминиевой пленки и металлизированная Гуляй-Поле

Quality Characteristics Appearance GradeItemA ClassQualifiedOff-gradeAppearanceCoatingBottom and surface color uniform. Coating thickness reaches parameters requiredBottom and surface color does not uniform. Coating thickness varies parameters required ≥10%Obvious un-uniformedJoint≤1pc/120m≤4pc/120m≤4pcPinhole≤4pc/m2 seen≤6pc/m2 seen≤6pc/m2Yellow spotNot allowedAllowed little bit but not affect stamping.Stamping problem.DamageNo fold, scratch, crush allowed.≤10cm/1m long.A lot Note: 1) Pinhole means aluminum particles sputtered to the film during vaccum metalisation process. Such defects refers to the visible hole size 1.0 mm maximum. 2) Yellow spot means that the film becomes slightly yellow. 3) No wrinkle is allowed in the joint of each interface, 0.64m deep of adhesive tape required. 4) Rewinding hardness of the roll must keep consistent. Mark can be seen when pressing by hand. 5) Backing release paper colour must be the same. Yellow and white must be stored separately. Attention should be paid to the yellow back colour. No significant deviation is observed with eye. Size SizeNominateAllowanceWidth0.64MA class(±2mm)Qualified(±5mm)Length120MA class(±0.5m)Qualified(±1.2m) Note: 1) No hardness of roll is specified. 2) No edge offset is greater than 3mm allowed. Roll surface flatness is less than 0.5 mm. 3) Special specifications can be ordered. Colour variation in the samel batch (1) No big colour variation is observed against the colour disc. (2) If big colour variation is observed against the colour disc, .the whole batch must be specially treated. Hot stamping articulation index: ItemDistribution areaIndexS typeM typeHot stamping clarityIn square area HGNo pin hole allowedNo pin hole allowedThick line in line areaNo break or stickNo break or stickHair line in grid areaClear above B area, no blank, no stick.Clear above B area, no blank, no stick. A little blank in B area Note: 1) Pinhole means defect blank of hot stamping. 2) Stamping conditions: 2# (pressure), 125-130°c, 0.75 0.8s. 3) When stamping is completed, wipe the stamping pattern in the clearer stamping area (as a minor area of flying gold) by hand, observe the palm, judge the metal flakes left on palm. The less the better. 4) Hardness is different to that of card type H1XX. It is appropriate to take H1XX M type as H5XX M type. 5) Test frequency: One for every 10 standard sample printing roll. Exam if there is release paper what the hardness is. Product Model and Property Electrochemical aluminum is also called hot stamping foil. It is made by vacuum aluminum metalisation. Its basic structure is the base film layer, peel layer, dyeing layer, metalised aluminium layer and adhesive layer etc. Low costs, continuous mechanical hot stamping makes this technology rapid promotion in the fields of industry. Printing effect is more rich and colorful. ModelApplicationPropertyStamping condition1Apply to gloss paper, ink printing paper.High gloss, wear-resistant and good stamping property90 120°C0.3 0.5s2Special for scroll stampingHigh gloss, wear-resistant and good stamping property.90 120°C0.3 0.5s3Suitable for paper and plastics.High gloss, wear-resistant and good stamping property.90 125°C0.3 0.5s4Suitable for fabric stamping and hot transfer printing.Heat resistant, bearing washing and kneading.90 130°C0.3 0.5s5Suitable for cigarette fine line stamping.Heat resistant, bearing washing and kneading.120 140°C0.3 0.5s6Suitable for leather stamping and hot transfer printing.Heat resistant, bearing washing and kneading. Note: The above hot stamping conditions are provided only as reference. Appropriate adjustment is essential according to different machine and stamping method.