WPX speed worm reducer gearbox speed reducer

WPX worm and worm gear speed reducer's features: 1.widely used in turbines, shaft liners and axletrees;good resistance to wear, with high precision in dimensions,low noise, advanced centric runningcastings.2.With air vent and highprecision.3.The structure is compact and the weight is large.4.Packing:wooden cases or can be according to customer's requriements.1. notice of installation1.1 The base-plate must be plane and stoutness and the base-plate must be screwed down and shock proof.1.2 The connecting shaft of prime mover, reducer and operation device must be coaxial installation.1.3 The diameter tolerance zone of input and output shaft is H6, the holes of fittings( such as couplings, belt-pully, sprocket wheel and so on) must properly mate the shaft, which prevents bearing from breakage because of over-loose mate.1.4 Drivers such as sprocker wheel and gear must be fitted close to bearings in order to reduce bending stress of hanging shaft.1.5 While assembling motor of WPD reducer, it is necessary that proper amount of butter applies to the warm shaft input hole and keyway, avoiding assembling too tightly and rusting after using for a long time.1.6 When ordering or using all kinds of WPD type, if the motor weight is binger than the common,supporting set is required.2.notice of usage2.1 Before using,please check carefully whether the reducer modle, distance, ratio, input connecting method , output shaft structure, input and output shaft direction and revolving direction accord with required.2.2 According to the requirement of selecting lubricant oil in the product manual. Please fill proper category and brand lubricant.And then screw on the vent-plug, unlock the small cone-plug of vent-plug.Only after doing these, reducer is already for startinh up running.The proper brand and adequate lubricant oil is required, replacing oil in time conforming to the request of product manual is also necessary, especially after using first 100hours, it is required refilling new oil.2.3 When abnormal circumstances occur, please stop and check reducer per solutions and reasons for faults of reducer(allowable highest oil temperature is 95, under this temperature limit, if oil temperature no more goes up, please let reducer continue running). speed of input shaft:1500r/minWP.WPK.WPW.WPWK(A.S.X.O.T.V) Input Power(kw)Model Ratio 10 15 20 25 30 40 50 60 40 0.4 0.33 0.26 0.24 0.22 0.16 0.14 0.12 50 0.65 0.52 0.40 0.37 0.34 0.27 0.24 0.20 60 1.00 0.82 0.65 0.590.54 0.45 0.40 0.32 70 1.60 1.35 1.10 0.96 0.82 0.67 0.61 0.52 80 2.20 1.781.36 1.28 1.20 0.90 0.80 0.75100 3.60 3.10 2.60 2.35 2.10 1.68 1.30 1.00120 5.20 4.35 3.503.25 3.00 2.20 1.90 1.50135 9.75 7.85 6.00 5.50 5.00 3.69 2.89 2.30147 10.71 8.436.18 5.71 5.23 3.843.09 2.52155 12.80 9.90 7.00 6.53 6.00 4.40 3.61 3.00175 17.30 13.6010.00 9.13 8.30 6.184.85 4.07200 22.60 18.20 13.86 12.75 11.67 8.78 6.71 5.5825033.20 27.40 21.60 20.00 18.4314.00 10.43 8.62