60 W Einfachausgang LED-Netzteil / LED DRIVER

MODEL PLC-60-24OUTPUTDCVOLTAGE 24V CONSTANT CURRENT REGION Note.6 16.8 24V RATEDCURRENT 2.5A CURRENTRANGE 0 2.5A RATEDPOWER 60W RIPPLE&NOISENOTE.2 2.4VP-P VOLTAGE ADJ RANGE 23.5 26V CURRENT ADJ. RANGE Note.5 1.875 2.575A VOLTAGETOLERANCENOTE.3 ±10% LINEREGULATION ±3.0% LOADREGULATION ±5.0% SETUP.RISEHOLD.TIME 1500ms / 230VAC 3000ms / 115VAC at full load INPUTVOLTAGERANGE 90 264VAC 127 370VDC FREQUENCYRANGE 47 63HZ POWER FACTOR PF≥ 0.9 at 75 100% load, 115VAC / 230VAC EFFICIENCY 87% AC CURRENT 0.8A/115VAC 0.4A/230VAC INRUSH CURRENT 40A/230VAC LEAKAGECURRENT 0.75mA/240VAC PROTECTIONOVER CURRENT 110%max Protection typeConstant current limiting,recovers automatically after fault condition is removed SHORT CIRCUIT Hiccup mode, recovers automatically after fault condition is removed. OVER VOLTAGE 28 32V Protection typeShut down o/p voltage,re-power on to recover. OVER TEMPERATURE 95± 10 (TSW1) detect on heatsink of power transistor Protection type : Shut down o/p voltage, recovers automatically after temperature goes down ENVIRONMENTWORKINGTIMP -30 +50(refer to output load derating curve) WORKINGHUMIDITY -20 95%Rhnon-condensing STORAGE TEMP HUMIDITY -40 +80 10 95%RH TEMPCOEFFICIENT ±0.03%(0 50) VIBRATION 10 500HZ,2G10min/1cycle period for 60 min each alongX,Y,Zaxes SAFETY&EMCSAFETYSTANDARDS UL1310 Class 2, TUV EN61347-1, EN61347-2-13, CAN/CSA C22.2 No. 223-M91(except for 48V) approved WITHSTAND VOLTAGE I/P-O/P:3.75KVAC I/P-FG:1.88KVAC O/P-FG:0.5KVAC ISOLATIONRESISTANCE I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH EMI CONDUCTICN& RADIATION Compliance to EN55015, EN55022 (CISPR22) Class B HARMONICCURRENT Compliance to EN61000-3-2 Class C (≥ 75% load) ; EN61000-3-3 EMS IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024,EN61547, light industry level, criteria A QTHERSMTBF 515Khrs min. MIL-HDBK-217F (25 ) DIMENSION 181.5*62*35mm (L*W*H) PACKING 0.41Kg; 30pcs/13.3Kg/0.67CUFT NOTE1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.Direct connecting to LEDs is not suggested for models with .RIPPLE & NOISE. > 10% and using additional drivers is highly recommended.3. Tolerance : includes set up tolerance, line regulation and load regulation.4. Please refer to OLP characteristics.5. Derating may be needed under low input voltage. Please check the derating curve for more details.6. Output voltage can be adjusted through the SVR1 on the PCB ; limit of output constant current level can be adjusted through the SVR2 on the PCB.7. Constant current operation region is within 70% 100% rated output voltage. This is the suitable operation region for LED related applications, but pleasereconfirm special electrical requirements for some specific system design.8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by thecomplete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.